The minimum requirements for achievement of the Certificate III in Watch and Clock Service and Repair are:
completion of all core units of competency listed below
completion of elective units to a total value of at least 73 points, chosen as described below:
watch and clock stream units from Group A to the value of at least 40 points; and
trade specialisation units from Group B to bring the total value to at least 73 points.
Units with prerequisites are marked with an asterisk. Points associated with prerequisites count towards the total (refer to units and prerequisites listing in Appendix 2, Volume 1).
Appropriate Group B elective units to the value of 16 points may be chosen from other endorsed Training Packages and accredited courses where those units are available for inclusion at Certificate III.
Registered Training Organisations must seek a determination from Manufacturing Skills Australia in respect of the allocation of points values for units of competency drawn from other Training Packages or accredited courses.
Note that the elective units listed below include all of the units that are approved for selection from the MEM Training Package for use in this qualification. This meets the NQC requirement that one sixth of the total units must be able to be selected from other qualifications in the same Training Package.
Only select units that would be suitable for occupational outcomes in a watch and clock service and repair environment.
Select all of the units from this list.
|
|
MEM12023A
|
Perform engineering measurements
|
MEM12024A
|
Perform computations
|
MEM13014B
|
Apply principles of occupational health and safety in the work environment
|
MEM14004A
|
Plan to undertake a routine task
|
MEM14005A
|
Plan a complete activity
|
MEM15002A
|
Apply quality systems
|
MEM15024A
|
Apply quality procedures
|
MEM16006A
|
Organise and communicate information
|
MEM16007A
|
Work with others in a manufacturing, engineering or related environment
|
MEM16008A
|
Interact with computing technology
|
MEM17003A
|
Assist in the provision of on the job training
|
MSAENV272B
|
Participate in environmentally sustainable work practices
|
-
Select units from this list to the value of at least 40 points.
|
|
|
MEM05001B
|
Perform manual soldering/desoldering, electrical/electronic components
|
4
|
MEM06007B
|
Perform basic incidental heat/quenching, tempering and annealing
|
2
|
MEM07005C
|
Perform general machining*
|
8
|
MEM09002B
|
Interpret technical drawing
|
4
|
MEM12002B
|
Perform electrical/electronic measurements
|
2
|
MEM18001C
|
Use hand tools
|
2
|
MEM21001A
|
Replace watch batteries, capacitors and bands
|
2
|
MEM21002A
|
Perform watch movement exchange *
|
2
|
MEM21003A
|
Perform watch case servicing, repair and refurbishment *
|
4
|
MEM21004A
|
Clean watch and clock components
|
2
|
MEM21005A
|
Diagnose faults in quartz watches *
|
2
|
MEM21006A
|
Service quartz watches *
|
4
|
MEM21007A
|
Service complex quartz watches *
|
4
|
MEM21008A
|
Service mechanical watches *
|
4
|
MEM21009A
|
Inspect, diagnose, adjust and repair mechanical watches *
|
4
|
MEM21010A
|
Service watch power generating systems *
|
2
|
MEM21011A
|
Service calendar and other dial indication mechanisms for watches *
|
4
|
MEM21012A
|
Service and repair mechanical watch oscillating systems *
|
4
|
MEM21013A
|
Service, test and adjust watch escapements *
|
4
|
MEM21014A
|
Service mechanical chronograph watches *
|
6
|
MEM21015A
|
Perform precision watch timing and adjustment *
|
6
|
MEM21016A
|
Install and set up clocks
|
2
|
MEM21017A
|
Service and repair clock timepieces
|
6
|
MEM21018A
|
Service clock escapements and oscillating systems *
|
4
|
MEM21019A
|
Service and repair clock striking mechanisms *
|
4
|
MEM21020A
|
Service and repair clock chiming mechanism *
|
6
|
MEM21021A
|
Restore clockwork mechanisms *
|
6
|
MEM21022A
|
Manufacture watch and clock components*
|
6
|
MEM21023A
|
Plan, set up and operate horological workshop or service centre
|
4
|
MEM30025A
|
Analyse a simple electrical system circuit*
|
4
|
-
Select units from the Certificate III Trade Specialisation units listed in Appendix I, Volume 1 of this Training Package to bring the total value of units to at least 73 points, including any prerequisites.
Appropriate specialisation units to the value of 16 points may be chosen from other endorsed Training Packages and accredited courses where those units are available for inclusion at Certificate III.